1-off exhaust system complete

UNBROKEN · Nov 29, 2020

Started with SPD downpipes and built the whole thing with 304 stainless 3” mandrel bends, Vibrant resonators and Magnaflow mufflers. Took me and a buddy about 10 hours start to finish.

UNBROKEN · Nov 29, 2020

Idle and rev.

UNBROKEN · Nov 29, 2020

I tried to get a decent launch but it shook the tires on the 1-2 shift.

dodges · Nov 29, 2020

Looks awesome great job

Possumcat · Nov 29, 2020

Nice job.

RED09GT · Nov 29, 2020

That sounds really good.

Great work.

How is the noise level?

Sch0227 · Dec 3, 2020

UNBROKEN said:

Where did you get this done at? I’m in TX as well and looking for the same thing

UNBROKEN · Dec 3, 2020

Sch0227 said:

I built it with a buddy.

Sch0227 · Dec 4, 2020

UNBROKEN said:

If you decide to build a rev.2 and wanna sell that one let me know!

Kruppa · Dec 4, 2020

UNBROKEN said:

Do you think if instead of 2 mufflers at the end it was 2 resonators you would get any noticeable difference in power? Obviously it would be louder. Just curious

UNBROKEN · Dec 4, 2020

None at all. Everything I put in is 3” straight through. There’s nothing baffled...it’s all as open as a straight pipe aside from the internal X in the main muffler.

Love Tractor · Dec 9, 2020

UNBROKEN said:

I've been keeping up with your build and I spoke with a guy who does custom work near me. He says he can do aluminized pipe custom for about $600 behind the downpipes. What's the drone like on your setup? I like the idea of having a 3" setup and spending a little less in case I want to bolt the stock stuff back on to sell/trade at some point. Was curious what your thoughts are since you seem to be quite knowledgeable on this stuff.

UNBROKEN · Dec 9, 2020

There’s no drone at all but there is some increase in volume when driving. I’m about to do a CLD/CCF/MLV treatment to the rear and hatch to knock that down.

Love Tractor · Dec 9, 2020

UNBROKEN said:

Thanks for the response. What are your thoughts on the aluminized vs the stainless pipe? The guy I spoke with said that the only difference woulld be longevity and that 10 years life expectancy in the south was reasonable. Does the 3" pipe help with lag, power, etc?

UNBROKEN · Dec 9, 2020

Aluminized would be fine in the south but the key is using mandrel bends. A 3” system done at a normal shop with crimp bends would effectively be about a 2.5” system....basically a waste of time IMHO. And I always subscribe to the bigger is better theory with boosted applications....especially turbos. 3” may be overkill for these things but overkill is better than too small.

FatGuyBuilds_YT · Dec 10, 2020

UNBROKEN said:

Aluminized would be fine in the south but the key is using mandrel bends. A 3” system done at a normal shop with crimp bends would effectively be about a 2.5” system....basically a waste of time IMHO. And I always subscribe to the bigger is better theory with boosted applications....especially turbos. 3” may be overkill for these things but overkill is better than too small.

are you the same person from the focus ST forum?

UNBROKEN · Dec 10, 2020

FatGuyBuilds_YT said:

Nope. Not on any Focus forums. I’m on a local Houston ST/RS FB group but that’s it.

GearHead_1 · Dec 20, 2020

Very nice system.

blkst · Dec 21, 2020

Do you mind sharing part numbers?
I want to do a custom 3" setup as well.

Sent from my SM-G975W using Tapatalk

NewportST · Apr 15, 2021

GREAT sounding kit! wonder how the mags would sound on a resonator delete? also, what part number magnaflow mufflers did you use?

Sign Up! To view all forums and unlock additional cool features

1-off exhaust system complete

4000 Post Club

4000 Post Club

Attachments

4000 Post Club

Attachments

New Member

Member

Member

Member

4000 Post Club

Member

Member

4000 Post Club

Member

4000 Post Club

Member

4000 Post Club

Member

4000 Post Club

1000 Post Club

Member

New Member