• Sign Up! To view all forums and unlock additional cool features

    Welcome to the #1 Explorer ST Forum and Explorer ST community dedicated to Explorer ST owners and enthusiasts. Register for an account, it's free and it's easy, so don't hesitate to join the Explorer ST Forum today!


JACK POINTS

STJIM

STJIM

Member
#1
Messages
308
Reactions
204
Points
37
Location
Punta Gorda, FL, USA
#1
Am I crazy or is there know where you can find proper jack points and procedures to lift your ST? Looked at web until my eyes fell out. I can find every vehicle built except a 2020 explorer. Don’t get me wrong I’ve lifted individual corners to replace wheels etc. I’m going to order a Quick Jack for the C8 and would like to use it for both vehicles.
 

OP
STJIM

STJIM

Member
Thread Starter #2
Messages
308
Reactions
204
Points
37
Location
Punta Gorda, FL, USA
Thread Starter #2
(no where) dang auto spell!
 

C

Cdubya

1000 Post Club
#3
Messages
1,732
Reactions
867
Points
262
Location
NE Ohio
Vehicle
2020 Explorer ST
#3
There is no front center jack point. The rear differential can be used for the rear.
 

OP
STJIM

STJIM

Member
Thread Starter #4
Messages
308
Reactions
204
Points
37
Location
Punta Gorda, FL, USA
Thread Starter #4
Thanks but I’m looking for the side jack points.
 

Frank T.

Frank T.

Member
#5
Messages
136
Reactions
66
Points
27
Location
Grimsby, ON, Canada
#5
If you get down beneath the vehicle you will find arrows pointing to where you can place the jack. Just behind the front wheels and just in front of the rear wheels.
 

OP
STJIM

STJIM

Member
Thread Starter #6
Messages
308
Reactions
204
Points
37
Location
Punta Gorda, FL, USA
Thread Starter #6
I read that and I guess I’m blind. I guess you get that way a t 70 HaHa.
I’m guessing they go on the edge of the pinch points. Thanks going back out with brighter light as eyesight goes at 70 too! Thanks! Jim
 

OP
STJIM

STJIM

Member
Thread Starter #7
Messages
308
Reactions
204
Points
37
Location
Punta Gorda, FL, USA
Thread Starter #7
Thanks so much. I did find them and will be making an eye appt. tomorrow!
Jim
 

Frank T.

Frank T.

Member
#8
Messages
136
Reactions
66
Points
27
Location
Grimsby, ON, Canada
#8
STJIM said:
Thanks so much. I did find them and will be making an eye appt. tomorrow!
Jim
Click to expand...
get yourself one of these. Once you locate the spot at the pinch welds it makes it a little easier to locate the floor Jack.... POTAUTO Universal Aluminum Grooved Magnetic Jack Pad Jacking Puck Pinch Weld (0.39) Inch Frame Rail Adapter (Qty 1, Red) https://www.amazon.ca/dp/B078J55SBW/ref=cm_sw_r_cp_api_fabc_44tZFbPWQ753S?_encoding=UTF8&psc=1
 

OP
STJIM

STJIM

Member
Thread Starter #9
Messages
308
Reactions
204
Points
37
Location
Punta Gorda, FL, USA
Thread Starter #9
Thanks Frank! Just ordered 4 of them. That will work great using the new Quick Jack system. Jim
 

Dgoebel57

Dgoebel57

Member
U.S. Air Force Veteran
#11
Messages
136
Reactions
89
Points
27
Location
Faribault, MN, USA
Vehicle
2020 Rapid Red ST
#11
Thanks to STJIM for bringing this up as it got me under my ST where I discovered that some dealership shop genius also couldn't figure out those (when you're under the side) well marked lift points and put their lift pads 4 inches forward under a (Not Intended for lift) area and damaged the protruding tab along that body/floor pan seam folding it over and cracking off paint. Damaged Body tab from Improper lifting of Explorer.jpg
Tape measure is in the proper lifting point section.
 

K

kkriskal

Member
#12
Messages
232
Reactions
84
Points
27
Location
Colorado Springs, CO, USA
#12
Dgoebel57 said:
Thanks to STJIM for bringing this up as it got me under my ST where I discovered that some dealership shop genius also couldn't figure out those (when you're under the side) well marked lift points and put their lift pads 4 inches forward under a (Not Intended for lift) area and damaged the protruding tab along that body/floor pan seam folding it over and cracking off paint. View attachment 2853
Tape measure is in the proper lifting point section.
Click to expand...
Oh no, I have to now go check mine in the garage
 

K

kkriskal

Member
#13
Messages
232
Reactions
84
Points
27
Location
Colorado Springs, CO, USA
#13
Ok, just went and checked mine, They seem to have placed in in between the arrows. However, it is a thin portion, not a flat one. Is it where it is supposed to go. I am not sure if I am being clear with my question, it is like a thin metal area, like the folded edge protruding downand Not a flat one like I expected.
 

K

kkriskal

Member
#14
Messages
232
Reactions
84
Points
27
Location
Colorado Springs, CO, USA
#14
Dgoebel57

Dgoebel57

Member
U.S. Air Force Veteran
#15
Messages
136
Reactions
89
Points
27
Location
Faribault, MN, USA
Vehicle
2020 Rapid Red ST
#15
kkriskal said:
Ok, just went and checked mine, They seem to have placed in in between the arrows. However, it is a thin portion, not a flat one. Is it where it is supposed to go. I am not sure if I am being clear with my question, it is like a thin metal area, like the folded edge protruding downand Not a flat one like I expected.
Click to expand...
The lift points are that edge you're looking at, if you look at the top of the Ford jack, it has a groove for that edge, the Potauto Adapter allows standard round plate topped jacks to lift without damaging that standing seam.
 

K

kkriskal

Member
#16
Messages
232
Reactions
84
Points
27
Location
Colorado Springs, CO, USA
#16
Dgoebel57 said:
The lift points are that edge you're looking at, if you look at the top of the Ford jack, it has a groove for that edge, the Potauto Adapter allows standard round plate topped jacks to lift without damaging that standing seam.
Click to expand...
Ok, thank you, then my seam is slightly damaged, it has a split in the seam on one side. Either they should change the jack design or change the mounting points.
 

Frank T.

Frank T.

Member
#17
Messages
136
Reactions
66
Points
27
Location
Grimsby, ON, Canada
#17
kkriskal said:
Thanks for sharing, can you leave this installed in the vehicle or do you have to attach it everytime your dealer needs to lift it
Click to expand...
They have magnets so they would stay in place, if you happen to forget them there. But I don’t think they would remain there permanently.
 

Frank T.

Frank T.

Member
#18
Messages
136
Reactions
66
Points
27
Location
Grimsby, ON, Canada
#18
kkriskal said:
Thanks for sharing, can you leave this installed in the vehicle or do you have to attach it everytime your dealer needs to lift it
Click to expand...
No. They dealer (i know, I know) should know exactly where to place their Jack’s.

These I would suggest are for the home mechanic type. I found it helps to locate and stabilize the lift when I use my floor jack.
 

K

kkriskal

Member
#19
Messages
232
Reactions
84
Points
27
Location
Colorado Springs, CO, USA
#19
Frank T. said:
No. They dealer (i know, I know) should know exactly where to place their Jack’s.

These I would suggest are for the home mechanic type. I found it helps to locate and stabilize the lift when I use my floor jack.
Click to expand...
Thank you.
 

L

Lightning Struck

Member
#20
Messages
210
Reactions
91
Points
27
Location
Waupun, WI, USA
#20
And where would you place the jack stands? I haven't gotten under mine yet, but lifting is only half the battle....
 

You must log in or register to reply here.

Explorer ST Posts



Top