• Sign Up! To view all forums and unlock additional cool features

    Welcome to the #1 Explorer ST Forum and Explorer ST community dedicated to Explorer ST owners and enthusiasts. Register for an account, it's free and it's easy, so don't hesitate to join the Explorer ST Forum today!


What Have You Done To Your Explorer ST Today

Jshaffer3819

Jshaffer3819

Member
U.S. Army Veteran
#622
Messages
471
Reactions
262
Points
37
Location
Kaiserslautern, Germany
#622
MikeyP said:
Installed the Steeda strut tower brace. No more fat, flimsy, stamped factory trash. Hopefully do the rear sway bar next week.
Click to expand...
Look good! Mine is getting powder coated red now. Looking forward to installing it.


Sent from my iPhone using Tapatalk
 

Z

zdubyadubya

Active Member
#625
Messages
813
Reactions
641
Points
232
Location
Utah
Vehicle
2020 ST
#625
Ford Guy said:
Oh really..I'm getting the common rattle from the stock flex pipes and waiting on SPD downpipes to ship which should hopefully be today.
I want to change out the stock flex pipes as is so you're saying once the DP's are on the rattling noise will get even worse?
I found new mesh flex pipes from Vibrant..anyone use these?

Part #: 62706
Description: Standard Flex Coupling w/ Inner Braid Liner, 2.25" I.D. x 6.00" Long

Option 2:
Part #: 62708
Description: Standard Flex Coupling w/ Inner Braid Liner, 2.25" I.D. x 8.00" Long
Click to expand...
Yes. It will get MUCH worse. I did not use these as I just used the Thermal mid-pipe kit from Whoosh (which uses Vibrant woven flex pipes), but I am sure any competent exhaust shop could weld either of those pieces into your existing setup.
 

F

Ford Guy

Member
#627
Messages
409
Reactions
113
Points
37
Location
Toronto, ON, Canada
#627
zdubyadubya said:
Yes. It will get MUCH worse. I did not use these as I just used the Thermal mid-pipe kit from Whoosh (which uses Vibrant woven flex pipes), but I am sure any competent exhaust shop could weld either of those pieces into your existing setup.
Click to expand...
Ya that's what I figured. It would probably be much cheaper to just buy the Vibrant mesh flex section and have a shop cut and weld to the existing mid pipes. I've asked Ron at whoosh for a quote on the Thermal mid pipe section. Thanks for the reply back.
 

M

mwinn

Member
#628
Messages
264
Reactions
203
Points
37
Location
Charlotte, NC, USA
#628
Jshaffer3819 said:
Nice! Did you have it sand blaster or leave the rough texture?


Sent from my iPhone using Tapatalk
Click to expand...
Was going to have it media blasted but after talking with the powder coating people I decided to leave as is. The blue pc filled in some of the texture. Real happy with the result. Completed the Steeda package, springs, rear sway bar and now this.
 

Jshaffer3819

Jshaffer3819

Member
U.S. Army Veteran
#630
Messages
471
Reactions
262
Points
37
Location
Kaiserslautern, Germany
#630
mwinn said:
Was going to have it media blasted but after talking with the powder coating people I decided to leave as is. The blue pc filled in some of the texture. Real happy with the result. Completed the Steeda package, springs, rear sway bar and now this.
Click to expand...
Cool, sounds like the exact same thing I am doing except I am painting mine red to match my calipers. The blue does look great though.


Sent from my iPhone using Tapatalk
 

M

mwinn

Member
#631
Messages
264
Reactions
203
Points
37
Location
Charlotte, NC, USA
#631
Jshaffer3819 said:
Cool, sounds like the exact same thing I am doing except I am painting mine red to match my calipers. The blue does look great though.


Sent from my iPhone using Tapatalk
Click to expand...
Can't go wrong with red. I went with the black cap bolts M8x1.25x25 and 45 for mounting. Gives it a nice finish. I know it most likely has little effect but you swear you can feel a difference once installed.
 

Jshaffer3819

Jshaffer3819

Member
U.S. Army Veteran
#632
Messages
471
Reactions
262
Points
37
Location
Kaiserslautern, Germany
#632
mwinn said:
Can't go wrong with red. I went with the black cap bolts M8x1.25x25 and 45 for mounting. Gives it a nice finish. I know it most likely has little effect but you swear you can feel a difference once installed.
Click to expand...
I noticed that. I was going to ask you where you got them. What is the 45? I really think it will make a difference. No reason to produce them if not. Can’t wait to install mine.


Sent from my iPhone using Tapatalk
 

N

NewYorkistanSux

Member
#633
Messages
44
Reactions
19
Points
2
Location
New York, NY, USA
#633
Bryantbjb said:
Dealer would not fix? Seems really close to delivery and not an easy place to damage. Just wondering.
Click to expand...
Have to bring it in for service, should be covered under warranty … first service opening isn’t til end of October though. :eek:
 

M

mwinn

Member
#634
Messages
264
Reactions
203
Points
37
Location
Charlotte, NC, USA
#634
Jshaffer3819 said:
I noticed that. I was going to ask you where you got them. What is the 45? I really think it will make a difference. No reason to produce them if not. Can’t wait to install mine.


Sent from my iPhone using Tapatalk
Click to expand...
45 is the length but you can probably get by with shorter. The bar comes with a spacer and longer bolts, one for each end. Careful when installing. My sausage fingers let one slip. Almost lost it in the bowels of the engine. You'll need to find a specialty bolt place. In my case it was Charlotte Bolt. I don't know what the finish is called but it looks anodized. No clue of the grade but I'm sure it's enough for this use. Guy told me they would not rust. Hope that helps.
 

Jshaffer3819

Jshaffer3819

Member
U.S. Army Veteran
#635
Messages
471
Reactions
262
Points
37
Location
Kaiserslautern, Germany
#635
mwinn said:
45 is the length but you can probably get by with shorter. The bar comes with a spacer and longer bolts, one for each end. Careful when installing. My sausage fingers let one slip. Almost lost it in the bowels of the engine. You'll need to find a specialty bolt place. In my case it was Charlotte Bolt. I don't know what the finish is called but it looks anodized. No clue of the grade but I'm sure it's enough for this use. Guy told me they would not rust. Hope that helps.
Click to expand...
Cool! Thanks for the good info.


Sent from my iPhone using Tapatalk
 

twin001

twin001

Member
#636
Messages
354
Reactions
252
Points
37
Location
Cincinnati, OH, USA
#636
Installed Fenfab catted downpipes today and did my e50 baseline pull today. No pics, sorry. If you are in the Cincinnati area and need the DPs installed check out Flowtek Customs in West Chester. Super nice people that did a great job and charged less than I was expecting. Plus, they had some sick customer cars to look at!

I'm still waiting for the Thermal to ship so for now it's Fenfab DPs with stock cat-back. FF DPs added a bit more of a throaty sound, but definitely did not make the exhaust sound much louder.....which is what I wanted! If anything you can actually hear the turbos spool up quite a bit more.
 

F

Ford Guy

Member
#637
Messages
409
Reactions
113
Points
37
Location
Toronto, ON, Canada
#637
twin001 said:
Installed Fenfab catted downpipes today and did my e50 baseline pull today. No pics, sorry. If you are in the Cincinnati area and need the DPs installed check out Flowtek Customs in West Chester. Super nice people that did a great job and charged less than I was expecting. Plus, they had some sick customer cars to look at!

I'm still waiting for the Thermal to ship so for now it's Fenfab DPs with stock cat-back. FF DPs added a bit more of a throaty sound, but definitely did not make the exhaust sound much louder.....which is what I wanted! If anything you can actually hear the turbos spool up quite a bit more.
Click to expand...
Thanks for sharing. I'm still desperately waiting for my SPD dp's uhhhhh. I heard from almost everyone who put dp's on hear the turbos spool more and they hear a throatier sound from the exhaust. Should see/feel power gains as well though.
 

Z

zdubyadubya

Active Member
#639
Messages
813
Reactions
641
Points
232
Location
Utah
Vehicle
2020 ST
#639
The random 3D weave carbon fiber on the dash bothered me and I had leftover forged carbon wrap from doing my hood, so I figured I would make the interior match..... and then I just kept going...

IMG_2123.JPG IMG_2122.JPG IMG_2124.JPG IMG_2125.JPG IMG_2126.JPG
 

You must log in or register to reply here.

Explorer ST Posts



Top