Search results

my favorite part of ceramic coating is that it makes the paint always look "wet" -- looking sharp

Here you go. You need a overall tire diameter of 30.7". To maintain the same amount of tire ratio or bulge you will need to run 275/40r22 tires in the front and 315/35r22 tires in the rear--otherwise it will look funny (a 275 tire installed on a 9" and a 10.5" wheel looks VERY different) or be...

Did some measuring today. The only way ANY spacer is fitting IN ADDITION TO a 10.5+30 wheel is with 305/35r22 tires (a +35 wheel will give you a little more room to play with spacer width). There is a metal backing plate on the rear side (by the door) of the font fender lining that my 305/40r22s...

I actually did the calculations required for this. Lemme dig em up and see how close they are to what you are looking at

I would 100% eff with something like this...

I'm probably gonna make my call based on your mockup/measurements (post lots of pics and videos) of a 305 or 315 tire on a 22x10.5+30 wheel plus 1.25" spacers. There is going to be serious inner fender liner trimming required and I am hoping no metal trimming. If metal trimming is needed, I am...

Nope. No issue. Also on lowering springs. IMO it makes the perfect stance. Remember that your camber increases as the suspension compresses. Nope. The front OEM track width is actually wider than the rear. That just evened it up.

Check the wheel threads. There are tons of posts of guys running BORA spacers with lots of pics of 1", 1.25", and 1.5". @BigRichard is correct about the sizing and stud length, but me personally, i thought the overflush look was a little better/more aggressive and ran 1.25" F and 1.5" R before...

Anecdotes are like opinions as in everyone has one, but my dad has a 800hp 12V Cummins with over 200k he has run nothing but Valvoline Premium Blue (per recommendation of Cummins) in for like 20 years. The Shaeffer reps have been hounding him for years to switch to their motor oil because they...

I run 6.5qts (per recommendation of ZFG tuning) of Amsoil Signature Series 5W-30 plus their EA15K43 filter and change every 5000 miles. I also run Blackstone oil reports with every change. You can check out the blackstone thread for results. Everything is running fantastic so far.

post lots of pics--hopefully there is no metal that needs to be trimmed.

Yes. I ran 1.25"F and 1.5"R with the street pack wheels before getting my forged 2-piece wheels. 1" spacers required stud trimming. Still run 0.25" slip on spacers in the rear with the forged wheels to even up the track width. OEM front track width is wider than the rear. And I really like...

i meant the inner felt liners. most guys with aftermarket forged wheels will not want to do new deeper concave ones, but even if you did, adding an additional 1.25" to outer clearance will definitely rub against the felt. I'm at +30 offset on a 10.5" wheel and I already touch at full lock. if...

I would definitely eff with a 1" widebody kit but i have concerns about fender liner clearance. I am assuming we would probably need to remove those? I would maybe look at doing 1.25" as that is the perfect size of spacer that doesn't require stud cutting.

The pinstripes are classy. I like that.

It does not. Listen to @Cdubya . Hub bore is 70.5 for all wheel sizes and engine sizes. Previous gen explorer and edge stuff will NOT fit. https://www.wheel-size.com/size/ford/explorer/2020/

its definitely a programming issue. I had the same problem with my new wheels/tires. Just because the sensors are 315MHz, doesn't fix everything. You need to have sensors that a programmed for the '21 explorer. Which means you will need to unmount your tires, install, and re-mount. I got the...

*cough* RS gasket *cough*

I did, and definitely not worth the money. They squealed horribly and I couldn't tell there was any additional power or less fade. They are a dealer installed item and my dealer had tossed my normal street pack brake pads on my back seat. I reinstalled them almost immediately. Just save your...

i'm pretty sure he is like batman. if we send up a signal @ZFGracing will he come find DetroitST