• Sign Up! To view all forums and unlock additional cool features

    Welcome to the #1 Explorer ST Forum and Explorer ST community dedicated to Explorer ST owners and enthusiasts. Register for an account, it's free and it's easy, so don't hesitate to join the Explorer ST Forum today!


Magnaflow or Borla?

Messages
15
Reactions
12
Points
2
Location
Discovery Bay, CA, USA
#1
I'm interested in upgrading my exhaust, but I don't want to increase the interior noise at freeway speeds. Especially the drone some systems create around 2000-2500 RPM.
 

UNBROKEN

4000 Post Club
Messages
4,592
Reactions
5,368
Points
352
Location
Houston, TX, USA
#2
You don’t want either one you listed then. You want the Thermal R&D built system Whoosh Motorsports sells.
 

OP
Baseballbum
Messages
15
Reactions
12
Points
2
Location
Discovery Bay, CA, USA
Thread Starter #3
What do they do different?
 

UNBROKEN

4000 Post Club
Messages
4,592
Reactions
5,368
Points
352
Location
Houston, TX, USA
#4
Theirs doesn’t drone. The Magnaflow system reportedly drones horribly...probably the worst of the bunch.
 

OP
Baseballbum
Messages
15
Reactions
12
Points
2
Location
Discovery Bay, CA, USA
Thread Starter #5
I wish I knew somebody who has made the change. It would suck to get it done and not like the sound. I'm an old guy. I like my quiet drives when I'm not stomping on it. LOL
 

F=MA

Active Member
Messages
947
Reactions
625
Points
232
Location
Wichita, KS, USA
#6
I previously had the Borla S-type and it had zero drone. I purchased the Borla before the Magnaflow was available. I personally prefer the lower tone of the Magnaflow setup. I currently have the Magnaflow system with stock downpipes. I mainly drive in town and/or on the urban freeways say 70 to 80 mph for 10 to 20 miles at a time. Drones at 1600 to 2000 rpm (range changes with burn-in) mainly in 9th and 10th gears which are overdrive gears. I put it in manual mode and 8th gear (which is also an overdrive gear) and the rpm's go up and the drone goes away. Don't have anyone at this time I trust to mig/tig weld helmholtz pipes on to kill the drone.
 

Last edited:
Messages
308
Reactions
201
Points
37
Location
Punta Gorda, FL, USA
#7
I’ve have the Borla S system for about 8,000 miles I drive about 50/50 town and freeway. 0 drone at anytime. i don’t believe there is any performance increase but it sure looks and sounds 100 % better. Jim
 

F=MA

Active Member
Messages
947
Reactions
625
Points
232
Location
Wichita, KS, USA
#10
Borla S Type vs Magnaflow #19515

I prefer the deeper tone of the magnaflow plus its a full length 2.5 inch system versus a partial 2.25 inch system. The 1600 thru 2000 rpm drone I can deal with by raising the rpm's by manually downshifting to 8th gear on the highway. In 8th gear rpms are high enough that the drone is gone. 8th gear is still an overdrive gear so it may be revving 2300 or so depending on speed. Sometimes I shift to 9th if I am going 80+ mph or so. Just was on a multi-hour road trip and it was fine dealing with the drone this way. You can rev up the magnaflow exhaust with the OEM downpipes and it does not crackle back like some I have heard with SPD downpipes.
 

Messages
26
Reactions
14
Points
2
Location
Florida
#11
Just picked up my st two days ago and I’ve been scouring the Internet trying to decide which exhaust I want. It’s between Borla atak or thermal.
 

Messages
84
Reactions
57
Points
17
Location
New Jersey
#13
How does it sound inside the cabin?
Sounds great. Has a very nice growl at WOT but zero drone.

Wife and I just got back from a round trip to Fort Lauderdale (from North NJ). Zero complaints from the wife and I enjoyed the sound when I got on it.
 

Messages
40
Reactions
29
Points
12
Location
Columbus, OH, USA
#14
I have the Borla S-type/ No drone to speak of. Only complaint is I get very random backfire type pops when downshifting after the system is warmed up.
 

Messages
86
Reactions
28
Points
17
Location
Des Moines, IA, USA
#15
Sounds great. Has a very nice growl at WOT but zero drone.

Wife and I just got back from a round trip to Fort Lauderdale (from North NJ). Zero complaints from the wife and I enjoyed the sound when I got on it.
Perfect, sounds like the exhaust for me. The girlfriend doesn't like the fake noise, so might as well add the real thing. I may have to keep the old though, apparently I am having auto start stop issue when remote starting...
 

GKSTCA

New Member
Messages
3
Reactions
4
Points
2
Location
Laguna Niguel, CA, USA
#16
I prefer Borla to all the rest , a matter of personal preference. I started out with the Borla S and switched to the ATAK. People on this site indicated the ATAK was too loud and I bought into it but its not true. But again I have a 2016 GT350, a 2018 Hellcat and a 2008 Will Cooksey Z06 so its all relative. our ST's are only 3.0 L and twin turbos, the turbos inherently quieten the exhaust note so in my opinion the Borla ATAK brings a throaty sound back into it. Its like a good tequila and all subject to personal opinion.
 

Messages
26
Reactions
14
Points
2
Location
Florida
#17
I prefer Borla to all the rest , a matter of personal preference. I started out with the Borla S and switched to the ATAK. People on this site indicated the ATAK was too loud and I bought into it but its not true. But again I have a 2016 GT350, a 2018 Hellcat and a 2008 Will Cooksey Z06 so its all relative. our ST's are only 3.0 L and twin turbos, the turbos inherently quieten the exhaust note so in my opinion the Borla ATAK brings a throaty sound back into it. Its like a good tequila and all subject to personal opinion.
I just ordered the Borla atak and a turbo smart dual bov. Should be here in a day or two. From what I’ve read everyone was saying thermal r&d but wanted that throaty sound
 

Messages
120
Reactions
61
Points
27
Location
South Palm Beach, FL, USA
#18
So after researching and listening to videos I like the thermal. Now do I get the mid pipes as well? Any advantage or dis advantage? Thank you for any suggestions.
Tommy
 

Messages
120
Reactions
61
Points
27
Location
South Palm Beach, FL, USA
#19
This is for a 2021. Sorry forgot to add that. Mid pipes would be downpipe back
 

F=MA

Active Member
Messages
947
Reactions
625
Points
232
Location
Wichita, KS, USA
#20
I believe the OEM downpipes are 2.5 in (correct me if I am wrong), OEM mid-pipes are 2.25 in and Thermal is 2.5 in. No sense leaving the smaller OEM mid-pipes (versus 2.5 in Thermal mid-pipes) in place to be the bottleneck of the entire system.
 



Top