• Sign Up! To view all forums and unlock additional cool features

    Welcome to the #1 Explorer ST Forum and Explorer ST community dedicated to Explorer ST owners and enthusiasts. Register for an account, it's free and it's easy, so don't hesitate to join the Explorer ST Forum today!


Springs installed wrong?

M

MuscleCarDan

New Member
#1
Messages
7
Reactions
0
Points
1
Location
San Francisco, CA, USA
Vehicle
2020 Explorer
#1
Dealer just installed my Steeda lowering springs, but the back is lower than the front. I strongly believe they are installed backwards. Lol

What do you guys think?
 

Attachments

C

Cdubya

1000 Post Club
#2
Messages
1,693
Reactions
842
Points
262
Location
NE Ohio
Vehicle
2020 Explorer ST
#2
at least from the picture, the rears do seem a little lower than typical but the fronts look about right. is it possible they left out the rubber spring perches in back? I dont think its possible to install rears up front and vice versa.
 

C

Cruising68

1000 Post Club
#3
Messages
1,627
Reactions
1,185
Points
262
Location
Chicago, IL, USA
#3
Doesn’t look right. When I did mine I recall it being pretty obvious which were front and rear.


Sent from my iPhone using Tapatalk
 

EDWYER

EDWYER

Member
#4
Messages
326
Reactions
156
Points
37
Location
NC
Vehicle
Black 2020 ST
#4
Take it back, it's def wrong.
 

OP
M

MuscleCarDan

New Member
Thread Starter #5
Messages
7
Reactions
0
Points
1
Location
San Francisco, CA, USA
Vehicle
2020 Explorer
Thread Starter #5
Yea when I look at other fresh installs on here you can definitely see a rake. This picture is fresh off the install no settling. I also forgot to mention the rear has a spacer as well.
 

C

Cdubya

1000 Post Club
#6
Messages
1,693
Reactions
842
Points
262
Location
NE Ohio
Vehicle
2020 Explorer ST
#6
take some wheel center-to-fender measurements and compare that to what others have posted here in the forum.
 

OP
M

MuscleCarDan

New Member
Thread Starter #7
Messages
7
Reactions
0
Points
1
Location
San Francisco, CA, USA
Vehicle
2020 Explorer
Thread Starter #7
Cdubya said:
take some wheel center-to-fender measurements and compare that to what others have posted here in the forum.
Click to expand...
Yea im going to try that and reach out to steeda tomorrow. I wonder if they are upside down?
 

EDWYER

EDWYER

Member
#8
Messages
326
Reactions
156
Points
37
Location
NC
Vehicle
Black 2020 ST
#8
MuscleCarDan said:
Yea when I look at other fresh installs on here you can definitely see a rake. This picture is fresh off the install no settling. I also forgot to mention the rear has a spacer as well.
Click to expand...
I hope they get it fixed for you. Spacer(s) has zero effect on lowering.
 

Cajun Heat

Cajun Heat

1000 Post Club
#9
Messages
1,198
Reactions
597
Points
262
Location
Katy, TX, USA
Vehicle
2022 Explorer ST
#9
MuscleCarDan said:
Yea im going to try that and reach out to Steeda tomorrow. I wonder if they are upside down?
Click to expand...
Not saying it is impossible to put the springs in upside-down (they would have to have really tried hard), but that should not affect the height. What I would guess is that Steeda sent you the wrong rear springs. Take a picture of the stamping on them and send that to Steeda.
 

C

ConspicuousConsumption

Member
#10
Messages
147
Reactions
34
Points
27
Location
2020 Whitehaven st, Washington DC 20007
Vehicle
2020 Explorer ST
#10
MuscleCarDan said:
Dealer just installed my Steeda lowering springs, but the back is lower than the front. I strongly believe they are installed backwards. Lol

What do you guys think?
Click to expand...
how much did the dealer charge you?
 

You must log in or register to reply here.

Explorer ST Posts



Top