UNBROKEN’s Iconic Silver ST build

[MattJ716]

A good friend is a Diode Dynamics dealer so I have these coming next week. View attachment 1168

Do you have access to these part numbers?

 

[AntD77]

Question, have you put the ST on scales yet to see what your vehicle weight is currently? Wondering how much different it is than stock.

 

[hotelmrrsn]

Well that was painfully easy to install. Love the finished look though. View attachment 6215

looks great, where did you guys pick up that rear hitch cover? Thanks in advance!

 

[BigRichard]

looks great, where did you guys pick up that rear hitch cover? Thanks in advance!

https://zeus3d.net/store/ols/products/explorer-hitch-cover/v/202-XPL-ST-HTC-PLN

 

[F=MA]

Installed the oemautoart front emblem on along with an ST emblem black out inlay that I found for $5 on eBay.
And now I’m gonna show you how to cheat. Technically you’re supposed to remove the whole damn front end to swap the oval. It’s too damn hot outside and I’m too damn lazy for all that. They send you a template to mark and drill for the new alignment pins...but they also have the old ones marked on the template...so I put both to work. A 1/4” drill bit right down the original pin locations to cut the pins off and the emblem just falls off. Drill for the new pins and get creative with some 3M VHB tape and you don’t even have to open the hood. I saved the nuts and I’ll throw them on when I install the intercooler. Done in 30 minutes. View attachment 1196 View attachment 1199 View attachment 1200 View attachment 1201

Sure glad I looked back through some posts and found this as I have had the red OEM autoart badges sitting in my office for a month or two dreading removing the front end again !!

 

[patricklb1]

They’re here...and they’re light AF. View attachment 1268 View attachment 1269

Having removed and remounted the stock 21's this past weekend to put in the IC I have a much better appreciation of the weight of your wheels, lol. Those stock 21's are f'ing heavy and I ain't gettin' any younger.

 

[UNBROKEN]

Having removed and remounted the stock 21's this past weekend to put in the IC I have a much better appreciation of the weight of your wheels, lol. Those stock 21's are f'ing heavy and I ain't gettin' any younger.

You should try the 24x14’s with 37x13.50’s on my F250…I’m way too old for that crap.

 

[patricklb1]

You should try the 24x14’s with 37x13.50’s on my F250…I’m way too old for that crap. View attachment 6950

No thanks!

 

[UNBROKEN]

Racing Brake 380mm rear rotors shipped today. Looks like I have some work to do soon.

 

[UNBROKEN]

Fresh from Racing Brake…
380mm rear rotors with caliper brackets to match, rear pads and a total surprise, braided stainless hoses for front and rear.

 

[UNBROKEN]

Also got the FenFab cold side IC pipe to replace the flattened stock part. I’ll be doing some measurements to compare after I cut the oem pipe up.

 

[patricklb1]

Also got the FenFab cold side IC pipe to replace the flattened stock part. I’ll be doing some measurements to compare after I cut the oem pipe up. View attachment 7017

Nice stuff. You're lucky, I'm sitting here in Dallas waiting on springs, exhaust and catch can. The catch can should be here pretty soon but the exhaust is late August and the springs are early October. F'ers all took my money though, lol. Since I have the standard brakes I am not looking forward to that bill, that could be the most expensive upgrade I'll have to do. I'll have to follow the Racing Brake table for upgrading.

 

[UNBROKEN]

I forgot…Pirelli PZ4’s in 315/35/22 coming next week.

 

[Nbk4t5e]

Goodies upon goodies!!


Sent from my iPhone using Tapatalk

 

[UNBROKEN]

And next week

Goodies upon goodies!!


Sent from my iPhone using Tapatalk

i didn’t even mention the new windshield it’s getting next Wednesday….because that one just pisses me off. lol

 

[Nbk4t5e]

That happens to drywall with me … haha.


Sent from my iPhone using Tapatalk

 

[UNBROKEN]

My mind says yay…my bank account says WTF are you thinking. lol

 

[edeyoung2]

So I got my stock calibrations off to zfg and he sent out a base tune within an hour, and I got this message. Did ever encounter this? He asked for my serial number and I haven't heard anything yet.

Sent from my SM-N981U using Tapatalk

 

[zdubyadubya]

So I got my stock calibrations off to zfg and he sent out a base tune within an hour, and I got this message. Did ever encounter this? He asked for my serial number and I haven't heard anything yet.

Sent from my SM-N981U using Tapatalk

You might have posted in the wrong thread (maybe you were looking for the ZFG thread?), but its no big deal. This means that the tuner "locked" the file to a specific RTD/MPIV2 device and yours cant read the file. That is why he asked for your S/N. Probably just made a mistake typing it in. He will turn around one that works.

 

[edeyoung2]

You might have posted in the wrong thread (maybe you were looking for the ZFG thread?), but its no big deal. This means that the tuner "locked" the file to a specific RTD/MPIV2 device and yours cant read the file. That is why he asked for your S/N. Probably just made a mistake typing it in. He will turn around one that works.

Sorry about that. Thanks for the help

Sent from my SM-N981U using Tapatalk