• Sign Up! To view all forums and unlock additional cool features

    Welcome to the #1 Explorer ST Forum and Explorer ST community dedicated to Explorer ST owners and enthusiasts. Register for an account, it's free and it's easy, so don't hesitate to join the Explorer ST Forum today!


Which fuse #'s to use for dashcam?

GTP

Member
Messages
82
Reactions
73
Points
17
Location
Indy
#1
Wondering what others' experience has been on which are best fuse choices for 12V power, and Switched Auxiliary power?

Also I have yet to spot a ground lug nearby the interior fusebox.
 

UNBROKEN

4000 Post Club
Messages
4,587
Reactions
5,363
Points
352
Location
Houston, TX, USA
#2
Top right fuse under the dash...can’t remember but it’s 27 or 37 I think. It’s switched 12V. You’ll need a mini fuse tap.
 

OP
GTP

GTP

Member
Messages
82
Reactions
73
Points
17
Location
Indy
Thread Starter #3
I will need 2 fuse taps actually.
Do you recall what you used for a ground post?
Do you run rear cam and if so did you route the cable through the hatch loom?
 

UNBROKEN

4000 Post Club
Messages
4,587
Reactions
5,363
Points
352
Location
Houston, TX, USA
#4
I only run a front cam. An Escort M1 that uses a single power wire for it and the Max 360 radar detector. I like easy.
 

Cdubya

1000 Post Club
Messages
1,693
Reactions
842
Points
262
Location
NE Ohio
Vehicle
2020 Explorer ST
#5
there's a grounding bolt below and to the side of the fusebox on the driver's side.

the rear camera cable: yes, run through the rubber cable passage. it'll fit.
 

OP
GTP

GTP

Member
Messages
82
Reactions
73
Points
17
Location
Indy
Thread Starter #6
Answering my own question: fuse taps to fuse# 37 (Accessory) and fuse# 29 (Always On)
 

Paul-J

New Member
Law Enforcement
Messages
2
Reactions
2
Points
2
Location
Alberta
Vehicle
2020 ST
#7
Answering my own question: fuse taps to fuse# 37 (Accessory) and fuse# 29 (Always On)
Thanks, I need to do that for a Rove R3 dash cam.
 

Messages
22
Reactions
12
Points
2
Location
San Francisco
Vehicle
2023 Ford Explorer ST
#8
For anybody looking for a good close ground that is not under the brake pedal, pop off the plastic panel next to dash. THere's a trim screw that connects to the ground that the fuse panel connects to as well.
 

Attachments

wifeys-ST

New Member
Messages
2
Reactions
1
Points
1
Location
Nunya
Vehicle
2020 Explorer ST
#9
Thanks for the info! I’ve always just soldered stuff in but this car is too nice to start cutting stuff up. In my experience these hardware kits always go bad after a year of two anyways so the fuse taps are nice.
 

Messages
190
Reactions
89
Points
27
Location
Sumner County TN
Vehicle
2025 Ford Explorer ST 400a
#12
Very cool. Who knew?

Note this does not deliver 12v and won’t power cameras with Parking Mode.
They should work. They will drop power when you park so they don’t kill your battery. I have 3 of them. My F150, my wife’s Edge and my new 25 ST. Work fine. Just make sure you get the one for your camera.


Sent from my iPhone using Tapatalk
 

wifeys-ST

New Member
Messages
2
Reactions
1
Points
1
Location
Nunya
Vehicle
2020 Explorer ST
#13
They should work. They will drop power when you park so they don’t kill your battery. I have 3 of them. My F150, my wife’s Edge and my new 25 ST. Work fine. Just make sure you get the one for your camera.


Sent from my iPhone using Tapatalk
Yea, they should work to power the camera when the car is running. it’s just a 5 Volt buck converter with a convenient plug and play jumper. But this will not enable parking mode if that’s what you’re wanting. Parking mode requires one 12v always constant wire and one 12v switched (accessory) wire going to the parking mode harness with low voltage cutoff. Still that’s a super neat solution if you dont care about parking mode.
 



Top