Yellow fogs

[BAD430BENZ]

Did this quick mod and really like the look.........

 

[zdubyadubya]

I agree!!!

 

[UNBROKEN]

I tried it on mine...it wasn’t working with the silver.

 

[Kirk ST]

Did this quick mod and really like the look.........

View attachment 6079

those look good. I also like how you painted all that trim below the grill/lights. Did you do the whole vehicle or just the front? Also, what are the black marks on your hood? function for heat/air or just decorative?

 

[BAD430BENZ]

those look good. I also like how you painted all that trim below the grill/lights. Did you do the whole vehicle or just the front? Also, what are the black marks on your hood? function for heat/air or just decorative?

all painted........

Mustang hood vents.......

 

[Crisisballer17]

Is that the yellow Lumin-X pre-cut tint? If so, did you do it while the fogs were still on the ST or did you remove them to install? I ordered them along with the rear reflector tint and the reverse light tint, and they just came today.

 

[BAD430BENZ]

Is that the yellow Lumin-X pre-cut tint? If so, did you do it while the fogs were still on the ST or did you remove them to install? I ordered them along with the rear reflector tint and the reverse light tint, and they just came today.

It is the Lamin-X but I went with a universal sheet....I think 9"x16" . I cut the sheet in half to make 4.5"x16" and did the install while on the vehicle . Super easy job ! I don't like the pre-cut because it doesn't really allow for much error . I also used a small hair dryer for install . Took me about an hour for both lights and that's just because I was being super careful with the trimming so I could tuck some of the excess between the light and body panel .

 

[Crisisballer17]

It is the Lamin-X but I went with a universal sheet....I think 9"x16" . I cut the sheet in half to make 4.5"x16" and did the install while on the vehicle . Super easy job ! I don't like the pre-cut because it doesn't really allow for much error . I also used a small hair dryer for install . Took me about an hour for both lights and that's just because I was being super careful with the trimming so I could tuck some of the excess between the light and body panel .

Thank you so much for the quick reply. I'll report back on how the pre-cut install goes. Also, the hair dryer tip is gold. Thank you!

 

[BAD430BENZ]

Thank you so much for the quick reply. I'll report back on how the pre-cut install goes. Also, the hair dryer tip is gold. Thank you!

Light use of the hair dryer just to make it a little more pliable .

 

[Crisisballer17]

I got the yellow foglight tint installed last night. Love the look on my Carbonized Gray ST!

 

[BAD430BENZ]

I got the yellow foglight tint installed last night. Love the look on my Carbonized Gray ST! View attachment 6094 View attachment 6095

Looks good !

 

[YUNGBECK]

Did this quick mod and really like the look.........

View attachment 6079

Can you please tell me where to get the black and red ford oval?

 

[BAD430BENZ]

Can you please tell me where to get the black and red ford oval?

I found it on Ebay but I haven't seen them since . You have to make sure they will fit your Explorer because there are plenty for an F150 .

 

[YUNGBECK]

Thank you!

 

[BAD430BENZ]

Thank you!

looks like there's a couple doing them on ebay

ebay listing number : 293413037773

ebay listing number : 313269703221

 

[YUNGBECK]

looks like there's a couple doing them on ebay

ebay listing number : 293413037773

ebay listing number : 313269703221

I appreciate the help, thank you.

 

[YUNGBECK]

Did this quick mod and really like the look.........

View attachment 6079

Where did you get the red and black ford oval?

 

[YUNGBECK]

Did this quick mod and really like the look.........

View attachment 6079

Where did you get the red and black
Oval?

 

[YUNGBECK]

Did this quick mod and really like the look.........

View attachment 6079

For the life of me I cannot understand how the lamin x fogs work. Been sitting here for an hour trying to figure out how they are supposed to work.

 

[Rick4345]

For the life of me I cannot understand how the lamin x fogs work. Been sitting here for an hour trying to figure out how they are supposed to work.

Did you ever get it figured out? I'm in the same boat you are, or were. My second set is supposed to be here today.